Inspecting an aluminum forging takes more than a dimensional check. A qualified supplier must be able to show records proving that alloy chemistry, heat-treated strength, surface defects, dimensions and finish are under control in every lot. This guide follows the three inspection stages at Al Forge Tech (AFT) in Taiwan, incoming (IQC), in-process (IPQC) and final (FQC), and explains the equipment used at each gate, what it catches, and seven questions buyers and SQEs can ask during a supplier audit.
Aluminum forgings go into suspension, braking and chassis parts where safety is on the line. Forging produces continuous grain flow and a dense structure, but whether a finished part conforms depends on four processes being verified one by one: material, tooling, heat treatment and machining. For a buyer, the practical test is not how long a supplier's equipment list is, but which risk each inspection covers and whether the records trace back to a lot.
I.What should be inspected before aluminum forgings ship?
| Stage | Inspection item | AFT equipment | What it catches | Records buyers can request |
|---|---|---|---|---|
| Incoming (IQC) | Alloy chemistry | Spectrometer ×1 | Mixed grades, out-of-spec chemistry | Mill certificate, incoming chemistry record |
| In-process (IPQC) | First/middle/last piece dimensions, die contour | Portable 3D scanner ×1, Zeiss CMM | Dimensional drift from die wear | First/middle/last piece inspection records |
| After heat treatment | Hardness, tensile strength, elongation | Hardness testers ×2, tensile testing machine | Low strength from incomplete solution or aging | Hardness and tensile test results |
| Surface defects | Surface-breaking flaws | Fluorescent penetrant line ×1 | Forging laps, cracks | Penetrant inspection records |
| Final (FQC): dimensions | Critical dimensions, GD&T, profiles | Zeiss CMM ×4, profile meter ×1 | Out-of-tolerance dimensions and profiles | CMM reports |
| Final (FQC): finish | Surface roughness, 2D dimensions, appearance | Surface roughness tester ×1, 2.5D automatic optical inspection | Excess roughness, cosmetic defects | Roughness and appearance records |
| Product validation | Fatigue life | Fatigue testing machine | Early failure under cyclic load | Fatigue test report (per project) |
Note: Equipment counts are from AFT company data. Items without a count are installed in-house; actual quantities may vary. The records provided are defined by the quality agreement between both parties.
How to use this table: map each inspection requirement on your drawing to the "Inspection item" column. Any requirement without matching equipment or records is a question to settle at the RFQ stage. For what to include in an RFQ, see our aluminum forging RFQ checklist.
II.Incoming inspection (IQC): confirming the alloy is right
AFT analyzes incoming chemistry with a spectrometer and checks it against the mill certificate. Forging alloys span the 2xxx to 7xxx series: 2014 and 2618 for high-strength or high-temperature parts, 6061, 6082 and 6110 for automotive chassis parts, and 7075 and 7050 for high-strength structural parts. Grades differ in their alloying elements. A mix-up means the wrong heat treatment recipe, missed hardness and strength targets, and a defect nobody can see on the surface.
AFT also has its own aluminum extrusion capability and produces part of its forging stock in-house, which shortens the material traceability chain.
- Analysis frequency. Ask how often incoming lots are analyzed and how results are matched to mill certificates.
- Material lot number. Check that the material lot number travels with the work order. This is where all traceability starts.
III.In-process inspection (IPQC): first, middle and last pieces vs. die wear
First, middle and last piece inspection
As a die runs, the cavity wears a little with each blow and part dimensions drift gradually. Checking only the first piece cannot catch late-lot changes. Checking the first, middle and last pieces reveals the trend across the whole lot.
3D scanning and die re-cutting
AFT uses a portable 3D scanner to confirm that the die contour matches the 3D design. When wear causes a deviation, the die is re-cut to adjust cavity depth, a job performed by AFT's partner toolmaker. Die accuracy determines dimensional consistency, which is why toolmaking is often called the soul of forging. To see why complex parts need several dies to form in stages, read Forging tonnage explained.
Production data: AFT's IoT system shows real-time production data from its CNC machines and part of its forging presses on a dashboard, which helps compare machine conditions when an anomaly occurs.
IV.After heat treatment: hardness and tensile testing
AFT runs 8 T4 solution treatment units and 7 T6 artificial aging units in-house, so forgings never leave the plant for heat treatment. Solution treatment dissolves the alloying elements evenly and locks them in with a rapid quench; artificial aging accelerates precipitation hardening so hardness reaches its peak. A small deviation in solution temperature, quench or aging time leaves a part looking exactly the same while its strength falls short.
Hardness testing
2 hardness testers. Fast and easy to sample often, so it suits monitoring every heat-treat load.
Tensile testing
Tensile testing machine. Measures tensile strength, yield strength and elongation; it needs specimens and is destructive.
Test standards
Common references are ASTM E8/E8M (tension) and ASTM E10 and E18 (hardness). The drawing specifies the actual standard.
Read more: Why aluminum forging heat treatment should not be outsourced
V.Fluorescent penetrant inspection: finding surface-breaking flaws
A fluorescent penetrant seeps into flaws that are open to the surface. After the excess penetrant is removed and a developer applied, flaws show up as bright indications under UV light. AFT operates a fluorescent penetrant inspection line, and ASTM E1417 is a common industry reference for the practice.
Keep in mind: FPI only detects flaws open to the surface. It cannot detect internal flaws that do not reach the surface. If your drawing calls for internal defect inspection, such as ultrasonic testing, raise it at the RFQ stage so both sides can agree on the method and who performs it.
Laps usually form where metal flow is poor, such as thin ribs or abrupt steps. They are best prevented at the design stage. AFT's engineering team proposes design changes during the design for manufacturability (DFM) review, supported by QForm forging simulation.
VI.Dimensions and finish: CMM, profile measurement and 2.5D optical inspection
- Zeiss CMM ×4. A touch probe measures hole positions, flatness, true position and other critical features that need high-precision judgment.
- Profile meter ×1. Measures curves and cross-section profiles, such as sealing faces and radii.
- Surface roughness tester ×1. Checks the roughness of machined surfaces such as mating and sealing faces.
- 2.5D automatic optical inspection. Uses imaging to measure 2D dimensions and appearance, reducing variation between human inspectors.
- Portable 3D scanner ×1. Captures the full shape for comparison with CAD, mainly for die contours and first-article shape checks.
With 52 CNC machining centers and 30 lathes in-house, AFT machines its forgings on site. Forged and machined dimensions are judged within the same measurement system, so no datum mismatch creeps in at a hand-off between plants. Learn more about our aluminum CNC machining services.
VII.Fatigue testing: validating safety parts
AFT has a fatigue testing machine and can run fatigue validation on parts or specimens as a project requires. Load conditions, cycle counts and acceptance criteria are usually set by the customer's design specification. It is best to write them into the validation plan during development rather than adding them just before production. For some R&D tests, AFT also works with the Metal Industries Research & Development Centre (MIRDC) in Taiwan.
VIII.Traceability and nonconformance handling: IATF 16949 in daily production
Traceability must link the material lot, forging date and press, heat-treat load, and machining and inspection records. During an audit, ask the supplier to demonstrate it live: pick any shipped lot number and time how long it takes to trace back to the material and heat treatment records. That tells you more than reading procedures.
AFT is also certified to ISO 14001:2015 for environmental management. To see how IATF 16949 works across AFT's product lines, read IATF 16949 is more than a certificate.
IX.Inspector training and knowledge transfer
Reading penetrant indications, programming CMM routines and grading cosmetic defects all take experience. IATF 16949 also requires measurement system analysis (MSA) to confirm that the gauges themselves are reliable. During an audit, buyers can ask for qualification and training records for key inspection stations.
X.SQE audit checklist: 7 questions for on-site or remote audits
How is incoming chemistry verified?
Ask how often spectrometer analysis is done and how results are matched to mill certificates. A good answer points straight to where the records are kept.
Where is heat treatment done?
Confirm whether it is in-house or outsourced, and how heat-treat loads are linked to part lot numbers. If outsourced, check how temperature records are obtained.
Which dimensions are checked on first, middle and last pieces?
Ask which features are measured at each point and how long the records are kept.
How is die wear detected?
Ask how die contours are checked, who decides when to re-cut a die, and how parts are re-verified afterwards.
Which parts get penetrant inspection?
Confirm which parts are inspected, to which practice standard, and how internal flaws are handled when required.
How is gauge accuracy assured?
Ask about calibration intervals for CMMs and hardness testers, and the results of measurement system analysis (MSA).
How fast can you trace an anomaly?
Pick any shipped lot number, have the supplier trace it back to material and heat treatment records on the spot, and ask them to explain their containment process.
Frequently asked questions
What inspections should aluminum forgings pass before shipment?
Typical pre-shipment inspections cover alloy chemistry, hardness and tensile results after heat treatment, fluorescent penetrant inspection, critical dimensions, surface roughness and appearance, plus fatigue validation for safety parts when the project requires it. The exact scope follows the customer drawing and quality agreement, so list the inspections and records you need at the RFQ stage.
What defects can fluorescent penetrant inspection find?
Fluorescent penetrant inspection finds flaws that break the surface, such as forging laps, cracks and surface-connected porosity. It cannot detect internal flaws that do not reach the surface. If your drawing requires internal defect inspection, such as ultrasonic testing, raise it when you request a quote so the method can be agreed in advance.
What is the difference between CMM measurement and 3D scanning?
A coordinate measuring machine (CMM) touches specific points with a probe and suits high-precision features such as hole positions, flatness and true position. A 3D scanner captures the whole shape at once and compares it with CAD, which suits die contour and first-article shape checks. The two are used together, not as substitutes.
How are hardness and strength confirmed after heat treatment?
Hardness testing is fast and suits monitoring every heat-treat load; tensile testing uses specimens to measure tensile strength, yield strength and elongation. AFT has 8 T4 and 7 T6 heat treatment units in-house, so heat treatment and the follow-up tests stay in one plant. Sampling plans and acceptance criteria follow the customer's requirements.
How are lots traced when a quality issue occurs?
AFT runs a traceability system under IATF 16949:2016 that links material lot, forging, heat-treat load, machining and inspection records. During an audit, ask the supplier to trace a randomly chosen shipped lot on the spot, and check how long it takes and whether the records are complete.
What inspection records can AFT provide to customers?
Records depend on the project and the quality agreement. Common examples are material certificates, dimensional reports, hardness and tensile results, and penetrant inspection records. List the documents and formats you need when you request a quote, and AFT's engineering and quality team will respond based on your drawing.
What quality and environmental certifications does AFT hold?
Al Forge Tech holds IATF 16949:2016 for automotive quality management and ISO 14001:2015 for environmental management. If your project needs other industry or special-process qualifications, raise them when you request a quote. AFT will first state whether it can meet them, then discuss next steps.
Send your inspection requirements to AFT's engineering and quality team
Send us your drawing and quality requirements. We will explain which stage and which equipment covers each inspection, and which records we can provide.
Send us:
- Drawings (STEP, IGES, DWG or PDF)
- Alloy and temper (for example, 6061-T6)
- Critical dimensions and any penetrant or fatigue requirements
- Annual volume and the inspection documents you need
Email [email protected]
Or send your details through our Contact Us page.
Browse: Hot forging | Aluminum CNC machining | Automotive parts | Motorcycle parts


